Proceedings of the ... Annual Convention of the American Railway Engineering Association, Volume 23Committee on Publications of the Association, 1922 - Railroad engineering List of members in v. 1-10. |
From inside the book
Results 1-5 of 99
Page 14
... less than thirty days after the filing of the application , the admission of the applicants shall be canvassed by letter - ballot among the members of the Board , and affirmative votes by two - thirds of its members shall elect the ...
... less than thirty days after the filing of the application , the admission of the applicants shall be canvassed by letter - ballot among the members of the Board , and affirmative votes by two - thirds of its members shall elect the ...
Page 19
... less than ten days after the vote is canvassed . Requirements for Election . 13. The persons who shall receive the highest number of votes for the offices for which they are candidates shall be declared elected . Tie Vote . 14. In case ...
... less than ten days after the vote is canvassed . Requirements for Election . 13. The persons who shall receive the highest number of votes for the offices for which they are candidates shall be declared elected . Tie Vote . 14. In case ...
Page 56
... less of a stilted character . For illustration , if one on the floor does not actually speak in the third person , the official report will have him down that way in the proceedings , whether or no . I have heard criticism of the ...
... less of a stilted character . For illustration , if one on the floor does not actually speak in the third person , the official report will have him down that way in the proceedings , whether or no . I have heard criticism of the ...
Page 108
... less than No. 6 H.D. for potentials less than 5,000 volts and No. 4 A.W.G. for higher potentials . No soft drawn wire should be permitted . Rule 220 ( a ) ( p . 90 ) . Clearances of Conductors and Wires at Crossings - Table 3 : The code ...
... less than No. 6 H.D. for potentials less than 5,000 volts and No. 4 A.W.G. for higher potentials . No soft drawn wire should be permitted . Rule 220 ( a ) ( p . 90 ) . Clearances of Conductors and Wires at Crossings - Table 3 : The code ...
Page 111
... less than 30 feet for potentials over 750 volts . Rule 263 ( b ) . No clearance of trolley wires less than 22 feet should be permitted . Specifically the 16 - foot clearance herein permitted is objected to . Rule 264 ( p . 142 ) . Code ...
... less than 30 feet for potentials over 750 volts . Rule 263 ( b ) . No clearance of trolley wires less than 22 feet should be permitted . Specifically the 16 - foot clearance herein permitted is objected to . Rule 264 ( p . 142 ) . Code ...
Other editions - View all
Common terms and phrases
American Railway Association American Railway Engineering Appendix ash pit average ballast boiler bolts bridges capacity cars Cast Iron cent Chairman Cinders classification yard Cleaning Committee recommends concrete connection construction Contractor cost crane creosote creosote oil crossing diameter Douglas Fir Electric engine house equipment feet fire floor Gravel handling Heavy Illinois Central Railroad inch inspection inspectors installed length Limnoria load located locomotive Manual material metal method Mikado miles motor operation Pacific paint piles pipe plans plates platform rail Railroad Railway Age Railway Engineering Association removed repair road San Leon sash shifts-Total side signal space specifications spikes standard Steam steel storage Sub-Committee submitted surface switches Teredo terminal timber tion traffic trains transfer table Transverse Fissures trestle trucks Untreated valve wall warehouse wire Wood Wood tar yard Zinc chloride Burnett
Popular passages
Page 546 - The manufacturer shall afford the inspector, without charge, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Page 49 - Let no man dare, when I am dead, to charge me with dishonor; let no man attaint my memory by believing that I could have engaged in any cause but that of my country's liberty and independence...
Page 501 - The purchaser may make the tests to govern the acceptance or rejection of the material in his own laboratory or elsewhere. Such tests, however, shall be made at the expense of the purchaser.
Page 211 - In the case of small or unimportant castings, a test to destruction on three castings from a lot may be substituted for the tension and bend tests. This test shall show the material to be ductile, free from injurious defects, and suitable for the purpose intended- A lot shall consist of all castings from one melt, in the same annealing charge.
Page 515 - For pipes 4-inch to 12-inch, inclusive, one class of special castings shall be furnished, made from Class D pattern. Those having spigot ends shall have outside diameters of spigot ends midway between the two standards of outside diameter as shown by Table No.
Page 537 - ... notice of its intention to terminate. Sixth: The provisions of this agreement shall Inure to the benefit of and be binding upon the successors and assigns of the parties.
Page 43 - Be it further Resolved, That this resolution be spread upon the minutes of this meeting and that certified copies be sent to Hon.
Page 1110 - Howard said he desired to call the attention of the members of the Association to the fact that this was the most representative meeting of the Association ever held.
Page 516 - For smaller sizes of pipes the letters may be 1 inch in length. The weight and the class letter shall be conspicuously painted in white on the inside of each pipe and special casting after the coating has become hard. ALLOWABLE PERCENTAGE OF VARIATION IN WEIGHT. SECTION 7. No pipe shall be accepted the weight of which shall be less than the standard...
Page 475 - Fine aggregate shall consist of sand, stone screenings, or other inert materials with similar characteristics, or a combination thereof, having clean, hard, strong, durable, uncoated grains and free from injurious amounts of dust, lumps, soft or flaky particles, shale, alkali organic matter, loam or other deleterious substances.