Proceedings of the Annual Convention of the American Railway Engineering and Maintenance-of-Way Association, Volume 23The Association, 1922 - Railroads List of members in v. 1- |
From inside the book
Results 1-5 of 100
Page 41
... road , will present the report of the Committee on Water Service . ( For report , see pp . 483-527 . ) The President : -The report of the Committee on Uniform General Contract Forms will be submitted by the Chairman , Mr. W. D. Faucette ...
... road , will present the report of the Committee on Water Service . ( For report , see pp . 483-527 . ) The President : -The report of the Committee on Uniform General Contract Forms will be submitted by the Chairman , Mr. W. D. Faucette ...
Page 49
... road , and he went to Virginia , taking me with him , but he remained in Virginia only a few months and came back as Assistant to the Second Vice - President , and finally was made General Manager of the Illinois Central . He was then ...
... road , and he went to Virginia , taking me with him , but he remained in Virginia only a few months and came back as Assistant to the Second Vice - President , and finally was made General Manager of the Illinois Central . He was then ...
Page 53
American Railway Engineering Association. a train . I was connected with the Santa Fe road , and a gentleman riding on the train , who discovered that I was the Engineer of the road , came around and spoke to me , and said he had built ...
American Railway Engineering Association. a train . I was connected with the Santa Fe road , and a gentleman riding on the train , who discovered that I was the Engineer of the road , came around and spoke to me , and said he had built ...
Page 54
... road . I had the pleasure during last year to be associated with Mr. Wallace in work in New York . I was a member of a committee that met every week for about three months . Mr. Wallace was chairman of the committee , and I can say he ...
... road . I had the pleasure during last year to be associated with Mr. Wallace in work in New York . I was a member of a committee that met every week for about three months . Mr. Wallace was chairman of the committee , and I can say he ...
Page 78
... road but no regular service has been established . A 50 - foot low - side gondola car was built to carry the containers , which fitted between the sides with only 2 - inch clearances and were secured in place . For freight service it ...
... road but no regular service has been established . A 50 - foot low - side gondola car was built to carry the containers , which fitted between the sides with only 2 - inch clearances and were secured in place . For freight service it ...
Contents
131 | |
159 | |
164 | |
165 | |
166 | |
167 | |
168 | |
225 | |
232 | |
263 | |
393 | |
427 | |
447 | |
483 | |
490 | |
784 | |
899 | |
18 | |
23 | |
28 | |
44 | |
59 | |
72 | |
86 | |
91 | |
99 | |
106 | |
177 | |
187 | |
Other editions - View all
Common terms and phrases
American Railway Association American Railway Engineering Appendix ash pit average ballast boiler bolts bridges capacity cars Cast Iron cent Chairman circuits classification yard Cleaning Clearance Committee recommends concrete connection construction Contractor cost crane crossing diameter double track Electric Electrolysis elevator engine house equipment feet fire floor freight house gang Grooved handling Illinois Central Railroad inch inspection installed length load located locomotive Manual material Maximum metal method Mikado miles Minimum motor operation paint passenger pipe plans plates platform rail railroad Railway Age Railway Engineering Association repair road Shawinigan Falls shifts-Total side space specifications spikes standard Steam steel storage Sub-Committee submitted surface swing bridges switches terminal tion Total traffic trains transfer table Transverse Fissures Trolley trucks valve vertical lift bridges wall Wallace warehouse weight width wire Wood yard
Popular passages
Page 550 - The manufacturer shall afford the inspector, without charge, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Page 505 - The purchaser may make the tests to govern the acceptance or rejection of the material in his own laboratory or elsewhere. Such tests, however, shall be made at the expense of the purchaser.
Page 43 - Be it further Resolved, That this resolution be spread upon the minutes of this meeting and that certified copies be sent to Hon.
Page 541 - The provisions of this agreement shall Inure to the benefit of and be binding upon the successors and assigns of the parties.
Page 1116 - Howard said he desired to call the attention of the members of the Association to the fact that this was the most representative meeting of the Association ever held.
Page 520 - For smaller sizes of pipes the letters may be 1 inch in length. The weight and the class letter shall be conspicuously painted in white on the inside of each pipe and special casting after the coating has become hard. ALLOWABLE PERCENTAGE OF VARIATION IN WEIGHT. SECTION 7. No pipe shall be accepted the weight of which shall be less than the standard...
Page 479 - Fine aggregate shall consist of sand, stone screenings, or other inert materials with similar characteristics, or a combination thereof, having clean, hard, strong, durable, uncoated grains and free from injurious amounts of dust, lumps, soft or flaky particles, shale, alkali organic matter, loam or other deleterious substances.
Page 126 - ... to that test. If either of these two additional specimens fails, the lot of tape represented by that sample shall be rejected. NOMINAL MINIMUM MINIMUM WEIGHT NET WEIGHT LENGTH PER ROLL, PER 100 PER POUND, LB. ROLLS, LB.
Page 524 - Specimen bars of the metal used, each being 26 inches long by 2 inches wide and i inch thick, shall be made without charge as often as the engineer may direct, and, in default of definite instructions, the contractor shall make and test at least one bar from each heat or run of metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the...
Page 519 - All pipes having the same outside diameter shall have the same inside diameter at both ends. The inside diameter of the lighter pipes of each standard outside diameter shall be gradually increased for a distance of about 6 inches from each...