Proceedings of the Annual Convention of the American Railway Engineering and Maintenance-of-Way Association, Volume 23The Association, 1922 - Railroads List of members in v. 1- |
From inside the book
Results 1-5 of 100
Page 19
American Railway Engineering Association. Ballots . 10. ( a ) Ballots shall be placed in an envelope , sealed and endorsed with the name of the voter , and mailed or deposited with the Secretary at any time previous to the closure of the ...
American Railway Engineering Association. Ballots . 10. ( a ) Ballots shall be placed in an envelope , sealed and endorsed with the name of the voter , and mailed or deposited with the Secretary at any time previous to the closure of the ...
Page 78
... placed upon motor trucks for delivery to the consignee . The trucking was not done by the railroad company . For ... placed are run out on the pier , where cranes transfer them to the steamer . At their destination , the boxes are ...
... placed upon motor trucks for delivery to the consignee . The trucking was not done by the railroad company . For ... placed are run out on the pier , where cranes transfer them to the steamer . At their destination , the boxes are ...
Page 107
... placed in the hands of work- men for interpretation . It is valuable as a reference book for use in the preparation of rules and specifications . Used in this manner the Code will be found most helpful . Rule 550 ( a ) ( p . 323 ) ...
... placed in the hands of work- men for interpretation . It is valuable as a reference book for use in the preparation of rules and specifications . Used in this manner the Code will be found most helpful . Rule 550 ( a ) ( p . 323 ) ...
Page 138
... placed under ties . Slag loaded by contract at 33 cents per cubic yard for first 20,000 yards and 23 cents per cubic yard for remainder , pit measurement . Contractor furnished all powder , labor and steam shovel for loading . Company ...
... placed under ties . Slag loaded by contract at 33 cents per cubic yard for first 20,000 yards and 23 cents per cubic yard for remainder , pit measurement . Contractor furnished all powder , labor and steam shovel for loading . Company ...
Page 139
... placed under tie . Slag loaded by contract at 30 cents per cubic yard . Contractor furnishing all powder , labor and steam shovel for loading , company furnishing pit engine and crew . Slag procured from dump of smelter at a royalty of ...
... placed under tie . Slag loaded by contract at 30 cents per cubic yard . Contractor furnishing all powder , labor and steam shovel for loading , company furnishing pit engine and crew . Slag procured from dump of smelter at a royalty of ...
Contents
131 | |
159 | |
164 | |
165 | |
166 | |
167 | |
168 | |
225 | |
232 | |
263 | |
393 | |
427 | |
447 | |
483 | |
490 | |
784 | |
899 | |
18 | |
23 | |
28 | |
44 | |
59 | |
72 | |
86 | |
91 | |
99 | |
106 | |
177 | |
187 | |
Other editions - View all
Common terms and phrases
American Railway Association American Railway Engineering Appendix ash pit average ballast boiler bolts bridges capacity cars Cast Iron cent Chairman circuits classification yard Cleaning Clearance Committee recommends concrete connection construction Contractor cost crane crossing diameter double track Electric Electrolysis elevator engine house equipment feet fire floor freight house gang Grooved handling Illinois Central Railroad inch inspection installed length load located locomotive Manual material Maximum metal method Mikado miles Minimum motor operation paint passenger pipe plans plates platform rail railroad Railway Age Railway Engineering Association repair road Shawinigan Falls shifts-Total side space specifications spikes standard Steam steel storage Sub-Committee submitted surface swing bridges switches terminal tion Total traffic trains transfer table Transverse Fissures Trolley trucks valve vertical lift bridges wall Wallace warehouse weight width wire Wood yard
Popular passages
Page 550 - The manufacturer shall afford the inspector, without charge, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Page 505 - The purchaser may make the tests to govern the acceptance or rejection of the material in his own laboratory or elsewhere. Such tests, however, shall be made at the expense of the purchaser.
Page 43 - Be it further Resolved, That this resolution be spread upon the minutes of this meeting and that certified copies be sent to Hon.
Page 541 - The provisions of this agreement shall Inure to the benefit of and be binding upon the successors and assigns of the parties.
Page 1116 - Howard said he desired to call the attention of the members of the Association to the fact that this was the most representative meeting of the Association ever held.
Page 520 - For smaller sizes of pipes the letters may be 1 inch in length. The weight and the class letter shall be conspicuously painted in white on the inside of each pipe and special casting after the coating has become hard. ALLOWABLE PERCENTAGE OF VARIATION IN WEIGHT. SECTION 7. No pipe shall be accepted the weight of which shall be less than the standard...
Page 479 - Fine aggregate shall consist of sand, stone screenings, or other inert materials with similar characteristics, or a combination thereof, having clean, hard, strong, durable, uncoated grains and free from injurious amounts of dust, lumps, soft or flaky particles, shale, alkali organic matter, loam or other deleterious substances.
Page 126 - ... to that test. If either of these two additional specimens fails, the lot of tape represented by that sample shall be rejected. NOMINAL MINIMUM MINIMUM WEIGHT NET WEIGHT LENGTH PER ROLL, PER 100 PER POUND, LB. ROLLS, LB.
Page 524 - Specimen bars of the metal used, each being 26 inches long by 2 inches wide and i inch thick, shall be made without charge as often as the engineer may direct, and, in default of definite instructions, the contractor shall make and test at least one bar from each heat or run of metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the...
Page 519 - All pipes having the same outside diameter shall have the same inside diameter at both ends. The inside diameter of the lighter pipes of each standard outside diameter shall be gradually increased for a distance of about 6 inches from each...