bethan Settlement.

HEATH, WILLIAM (1737-1814), American soldier, was born in Roxbury, Massachusetts, on the 2nd of March 1737 (old style). He was brought up as a farmer and had a passion for military exercises. In 1765 he entered the Ancient and Honourable Artillery Company of Boston, of which he became commander in 1770. In the same year he wrote to the Boston Gazette letters signed "A Military Countryman," urging the necessity of military training. He was a member of the Massachusetts General Court from 1770 to 1774, of the provincial committee of safety, and in 1774-1775 of the provincial congress. He was commissioned a provincial brig.-general in December 1774, directed the pursuit of the British from Concord (April 19, 1775), was promoted to be provincial major-general on the 20th of June 1775, and two days later was commissioned fourth brig.-general in the Continental Army. He became major-general on the 9th of August 1776, and was in active service around New York until early the next year. In January 1777 he attempted to take Fort Independence, near Spuyten Duyvil, then garrisoned by about 2000 Hessians, but at the first sally of the garrison his troops became panic-stricken and a few days later he withdrew. Washington reprimanded him and never again entrusted to him any important operation in the field. Throughout the war, however, Heath was very efficient in muster service and in the barracks. From March 1777 to October 1778 he was in command of the Eastern Department with headquarters at Boston, and had charge (Nov. 1777-Oct. 1778) of the prisoners of war from Burgoyne's army held at Cambridge, Massachusetts. In May 1779 he was appointed a commissioner of the Board of War. He was placed in command of the troops on the E. side of the Hudson in June 1779, and of other troops and posts on the Hudson in November of the same year. In July 1780 he met the French allies under Rochambeau on their arrival in Rhode Island; in October of the same year he succeeded Arnold in command of West Point and its dependencies; and in August 1781, when Washington went south to meet Cornwallis, Heath was left in command of the Army of the Hudson to watch Clinton. After the war he retired to his farm at Roxbury, was a member of the state House of Representatives in 1788, of the Massachusetts convention which ratified the Federal Constitution in the same year, and of the governor's council in 1789-1790, was a state senator (1791-1793), and in 1806 was elected lieutenant-governor of Massachusetts but declined to serve. He died at Roxbury on the 24th of January 1814, the last of the major-generals of the War of American Independence.

See Memoirs of Major-General Heath, containing Anecdotes, Details of Skirmishes, Battles and other Military Events during the American War, written by Himself (Boston, 1798; frequently reprinted, perhaps the best edition being that published in New York in 1901 by William Abbatt), particularly valuable for the descriptions of Lexington and Bunker Hill, of the fighting around New York, of the controversies with Burgoyne and his officers during their stay in Boston, and of relations with Rochambeau; and his correspondence, The Heath Papers, vols. iv.-v., seventh series, Massachusetts Historical Society Collections (Boston, 1904-1905).

HEATH, the English form of a name given in most Teutonic dialects to the common ling or heather (Calluna vulgaris), but now applied to all species of Erica, an extensive genus of monopetalous plants, belonging to the order Ericaceae. The heaths are evergreen shrubs, with small narrow leaves, in whorls usually

FIG. I. Calluna vulgaris.

sepals, and a 4-cleft campanulate or tubular corolla, in many species more or less ventricose or inflated; the dry capsule is 4-celled, and opens, in the true Ericae, in 4 segments, to the middle of which the partitions adhere, though in the ling the valves separate at the dissepiments. The plants are mostly of low growth, but several African kinds reach the size of large bushes, and a common South European species, E. arborea, occasionally attains almost the aspect and dimensions of a tree. One of the best known and most interesting of the family is the common heath, heather or ling, Calluna vulgaris (fig. 1), placed by most botanists in a separate genus on account of the peculiar dehiscence of the fruit, and from the coloured calyx, which extends beyond the corolla, having a whorl of sepal-like bracts beneath. This shrub derives some economic importance from its forming the chief vegetation on many of those extensive wastes that occupy so large a portion of the more sterile lands of northern and western Europe, the usually desolate appearance of which is enlivened in the latter part of summer by its abundant pink blossoms. When growing erect to the height of 3 ft. or more, as it often does in sheltered places, its purple stems, closeleaved green shoots and feathery spikes of bell-shaped flowers render it one of the handsomest of the heaths; but on the bleaker elevations and more arid slopes it frequently rises only a few inches above the ground. In all moorland countries the ling is applied to many rural purposes; the larger stems are made into brooms, the shorter tied up into bundles that serve as brushes, while the long trailing shoots are woven into baskets. Pared up with the peat about its roots it forms a good fuel, often the only one obtainable on the drier moors. The shielings of the Scottish Highlanders were formerly constructed of heath stems, cemented together with peat-mud, worked into a kind of mortar with dry grass or straw; hovels and sheds for temporary purposes are still sometimes built in a similar way, and roofed in with ling. Laid on the ground, with the flowers above, it forms a soft springy bed, the luxurious couch of the ancient Gael, still gladly resorted to at times by the hill shepherd or hardy deer-stalker. The young shoots were in former days employed as a substitute for hops in brewing, while their astringency rendered them valuable as a tanning material in Ireland and the Western Isles. They are said also to have been used by the Highlanders for dyeing woollen yarn yellow, and other colours are asserted to have been obtained from them, but some writers appear to confuse the dyer's-weed, Genista tinctoria, with the heather. The young juicy shoots and the seeds, which remain long in the capsules, furnish the red grouse of Scotland with the larger portion of its sustenance; the ripe seeds are eaten by many birds. The tops of the ling afford a considerable part of the winter fodder of the hill flocks, and are popularly supposed to communicate the fine flavour to Welsh and Highland mutton, but sheep seldom crop heather while the mountain grasses and rushes are sweet and accessible. Ling has been suggested as a material for paper, but the stems are hardly sufficiently fibrous for that purpose. The purple or fine-leaved heath, E. cinerea (fig. 2), one of the most beautiful of the genus, abounds on the lower moors and commons of Great Britain and western Europe, in such situations being sometimes more prevalent than the ling. The flowers of both these species yield much honey, furnishing a plentiful supply to the bees in moorland districts; from this heath honey the Picts probably brewed the mead said by Boetius to have been made from the flowers themselves.

The genus contains about 420 known species, by far the greater part being indigenous to the western districts of South Africa,

FIG. 2. Erica cinerea.

The Cape heaths have long been favourite objects of horticulture. In the warmer parts of Britain several will bear exposure to the cold of ordinary winters in a sheltered border, but most need the protection of the conservatory. They are sometimes raised from seed, but are chiefly multiplied by cuttings "struck" in sand, and afterwards transferred to pots filled with a mixture of black peat and sand; the peat should be dry and free from sourness. Much attention is requisite in watering heaths, as they seldom recover if once allowed to droop, while they will not bear much water about their roots: the heathhouse should be light and well ventilated, the plants requiring sun, and soon perishing in a close or permanently damp atmosphere; in England little or no heat is needed in ordinary seasons. The European heaths succeed well in English gardens, only requiring a peaty soil and sunny situation to thrive as well as in their native localities: E. carnea, mediterranea, ciliaris, vagans, and the pretty cross-leaved heath of boggy moors, E. Tetralix, are among those most worthy of cultivation. The beautiful largeflowered St Dabeoc's heath, belonging to the closely allied genus Dabeocia, is likewise often seen in gardens. It is found in boggy heaths in Connemara and Mayo, and is also native in West France, Spain and the Azores.

A beautiful work on heaths is that by H. C. Andrews, containing coloured engravings of nearly 300 species and varieties, with descriptions in English and Latin (4 vols., 1802-1805).

HEATHCOAT, JOHN (1783-1861), English inventor, was born at Duffield near Derby on the 7th of August 1783. During his apprenticeship to a framesmith near Loughborough, he made an improvement in the construction of the warp-loom, so as to produce mitts of a lace-like appearance by means of it. He began business on his own account at Nottingham, but finding himself subjected to the intrusion of competing inventors he removed to Hathern. There in 1808 he constructed a machine capable of producing an exact imitation of real pillow-lace. This was by far the most expensive and complex textile apparatus till then existing; and in describing the process of his invention Heathcoat said in 1836, "The single difficulty of getting the diagonal threads to twist in the allotted space was so great that, if now to be done, I should probably not attempt its accomplishment." Some time before perfecting his invention, which he patented in 1809, he removed to Loughborough, where he entered into partnership with Charles Lacy, a Nottingham manufacturer; but in 1816 their factory was attacked by the Luddites and their 55 lace frames destroyed. The damages were assessed in the King's Bench at £10,000; but as Heathcoat declined to expend the money in the county of Leicester he never received any part of it. Undaunted by his loss, he began at once to construct new and greatly improved machines in an unoccupied factory at Tiverton, Devon, propelling them by water-power and afterwards by steam. His claim to the inven

and a patent was taken out by a clever workman for a similar machine, which was decided at a trial in 1816 to be an infringement of Heathcoat's patent. He followed his great invention by others of much ability, as, for instance, contrivances for ornamenting net while in course of manufacture and for making ribbons and platted and twisted net upon his machines, improved yarn spinning-frames, and methods for winding raw silk from cocoons. He also patented an improved process for extracting and purifying salt. An offer of £10,000 was made to him in 1833 for the use of his processes in dressing and finishing silk nets, but he allowed the highly profitable secret to remain undivulged. In 1832 he patented a steam plough. Heathcoat was elected member of parliament for Tiverton in 1832. Though he seldom spoke in the House he was constantly engaged on committees, where his thorough knowledge of business and sound judgment were highly valued. He retained his seat until 1859, and after two years of declining health he died on the 18th of January 1861 at Bolham House, near Tiverton.

HEATHCOTE, SIR GILBERT (c. 1651-1733), lord mayor of London, belonged to an old Derbyshire family and was educated at Christ's College, Cambridge, afterwards becoming a merchant in London. His trading ventures were very successful; he was one of the promoters of the new East India company and he emerged victorious from a contest between himself and the old East India company in 1693; he was also one of the founders and first directors of the bank of England. In 1702 he became an alderman of the city of London and was knighted; he served as lord mayor in 1711, being the last lord mayor to ride on horseback in his procession. In 1700 Heathcote was sent to parliament as member for the city of London, but he was soon expelled for his share in the circulation of some exchequer bills; however, he was again elected for the city later in the same year, and he retained his seat until 1710. In 1714 he was member for Helston, in 1722 for New Lymington, and in 1727 for St Germans. He was a consistent Whig, and was made a baronet eight days before his death. Although extremely rich, Heathcote's meanness is referred to by Pope; and it was this trait that accounts largely for his unpopularity with the lower classes. He died in London on the 25th of January 1733 and was buried at Normanton, Rutland, a residence which he had purchased from the Mackworths.

A descendant, Sir Gilbert John Heathcote, Bart. (1795-1867), was created Baron Aveland in 1856; and his son Gilbert Henry, who in 1888 inherited from his mother the barony of Willoughby de Eresby, became 1st earl of Ancaster in 1892.

HEATHEN, a term originally applied to all persons or races who did not hold the Jewish or Christian belief, thus including Mahommedans. It is now more usually given to polytheistic races, thus excluding Mahommedans. The derivation of the word has been much debated. It is common to all Germanic languages; cf. German Heide, Dutch heiden. It is usually ascribed to a Gothic haipi, heath. In Ulfilas' Gothic version of the Bible, the earliest extant literary monument of the Germanic languages, the Syrophoenician woman (Mark vii. 26) is called haipno, where the Vulgate has gentilis. "Heathen," i.e. the people of the heath or open country, would thus be a translation of the Latin paganus, pagan, i.e. the people of the pagus or village, applied to the dwellers in the country where the worship of the old gods still lingered, when the people of the towns were Christians (but see PAGAN for a more tenable explanation of that term). On the other hand it has been suggested (Prof. S. Bugge, Indo-German. Forschungen, v. 178, quoted in the New English Dictionary) that Ulfilas may have adopted the word from the Armenian hetanos, i.e. Greek Ovn, tribes, races, the word used for the "Gentiles" in the New Testament. Gentilis in Latin, properly meaning "tribesman," came to be used of foreigners and non-Roman peoples, and was adopted in ecclesiastical usage for the non-Christian nations and in the Old Testament for non-Jewish races.

HEATHFIELD, GEORGE AUGUSTUS ELIOTT, BARON (17171790), British general, a younger son of Sir Gilbert Eliott, Bart.,

of Stobs, Roxburghshire, was born on the 25th of December 1717, and educated abroad for the military profession. As a volunteer he fought with the Prussian army in 1735 and 1736, and then entered the Grenadier Guards. He went through the war of the Austrian Succession, and was wounded at Dettingen, rising to be lieutenant-colonel in 1754. In 1759 he became colonel of a new regiment of light horse (afterwards the 15th Hussars) and became well known for the efficiency which it displayed in the subsequent campaigns. He became lieutenant-general in 1765. In 1775 he was selected to be governor of Gibraltar (q.v.), and it is in connexion with his magnificent defence in the great siege of 1779 that his name is famous. His portrait by Sir Joshua Reynolds is in the National Gallery. In 1787 he was created Baron Heathfield of Gibraltar, but died on the 6th of July 1790. He had married in 1748 the heiress of the Drake family, to which Sir Francis Drake belonged. His son, the 2nd baron, died in 1813 and the peerage became extinct, but the estates went to the family of Eliott-Drake (baronetcy of 1821) through his sister.

might be fixed in the middle of the apartment. The fixing of stoves of this kind entails the laying of pipes or ducts from the open to convey fresh air to the back of the stove. With closed stoves much less heat is wasted, and consequently less fuel is burned, than with open grates, but they often cause an unpleasant sensation of dryness in the air, and the products of combustion also escape to some extent, rendering this method of heating not only unpleasant but sometimes even dangerous. The method in Great Britain is almost entirely confined to places of public assembly, but in

Closed stoves.

FIG. I.

FIG. 2.

The object of all heating apparatus is the transference of heat from the fire to the various parts of the building it is intended to warm, and this transfer may be effected by radiation, by conduction or by convection. An open fire acts by radiation; it warms the air in a room by first warming the walls, floor, ceiling and articles in the room, and these in turn warm the air. Therefore in a room with an open fire the air is, as a rule, less heated than the walls. In many forms of fireplaces fresh air is brought in and passed around the back and sides of the stove before being admitted into the room. A closed stove acts mainly by convection; though when heated to a high temperature it gives out radiant heat. Windows have a chilling effect on a room, and in calculations extra allowance should be made for window

areas.

There are a number of methods available for adoption in the heating of buildings, but it is a matter of considerable difficulty to suit the method of warming to the class of building to be warmed. Heating may be effected by one of the following systems, or installations may be so arranged as to combine the advantages of more than one method: open fires, closed stoves, hot-air apparatus, hot water circulating in pipes at low or at high pressure, or steam at high or low pressure.

The open grate still holds favour in England, though in America and on the continent of Europe it has been superseded Open fires.

by the closed stove. The old form of open fire is certainly wasteful of fuel, and the loss of heat up the chimney and by conduction into the brickwork backing of the stove is considerable. Great improvements, however, have been effected in the design of open fireplaces, and many ingenious contrivances of this nature are now in the market which combine efficiency of heating with economy of fuel. Unless suitable fresh air inlets are provided, this form of stove will cause the room to be draughty, the strong current of warm air up the flue drawing cold air in through the crevices in the doors and windows. The best form of open fireplace is the ventilating stove, in which fresh air is passed around the back and sides of the stove before being admitted through convenient openings into the room. This has immense advantages over the ordinary type of fireplace. The illustrations show two forms of ventilating fireplace, one (fig. 1) similar in appearance to the ordinary domestic grate, the other (fig. 2) with descending smoke flue suitable for hospitals and public rooms, where it

Gas fires.

Gas fires, as a substitute for the open coal fire, have many points in their favour, for they are conducive to cleanliness, they need but little attention, and the heat is easily controlled. On the other hand, they may give off unhealthy fumes and produce unpleasant odours. They usually take the form of cast iron open stoves fitted with a number of Bunsen burners which heat perforated lumps of asbestos. The best form of stove is that with which perfect combustion is most nearly attained, and to which a pan of water is affixed to supply a desirable humidity to the air, the gas having the effect of drying the atmosphere. With another form of gas stove coke is used in place of the perforated asbestos; the fire is started with the gas, which, when the coke is well alight, may be dispensed with, and the fire kept up with coke in the usual way.

Electrical heating.

Oil stoves.

Electrical heating appliances have only recently passed the experimental stage; there is, however, undoubtedly a great future for electric heating, and the perfecting of the stove, together with the cheapening of the electric current, may be expected to result in many of the other stoves and convectors being superseded. Hitherto the large bill for electric energy has debarred the general use of electrical heating, in spite of its numerous advantages. Oils are powerful fuels, but the high price of refined petroleum, the oil generally preferred, precludes its widespread use for many purposes for which it is suitable. In small stoves for warming and for cooking, petroleum presents some advantages over other fuels, in that there is no chimney to sweep, and if well managed no unpleasant fumes, and the stoves are easily portable. On the other hand, these stoves need a considerable amount of attention in filling, trimming and cleaning, and there is some risk of explosion and damage by accidental leaking and smoking. Crude or unrefined petroleum needs a special air-spray pressure burner for its use, and this suffers from the disadvantage of being noisy. Gas and oil radiators would be more properly termed " convectors," since they warm mainly by convected currents. They are similar in appearance to a hot-water or steam radiator, and, indeed, some are designed to be filled with water and used as such. They should always be fitted with a pan of water to supply the necessary humidity to the warmed air, and a flue to carry off any disagreeable fumes.

Warm air.

the apparatus, and if properly installed will give as good effects as it is possible to obtain. The system is especially suitable for churches, assembly halls and large rooms. A stove of special design is placed in a chamber in the basement or cellar, and cold fresh air is passed through it, and led by means of flues to the various apartments for distribution by means of easily regulated inlet valves. To prevent the atmosphere from becoming unduly dry a pan of water is fitted to the stove; this serves to moisten the air before it passes into the distributing flues. If each distributing flue is connected by means of a mixing valve with a cold-air flue, the warmth of the incoming air can be regulated to a nicety (see VENTILATION).

Low pressure hot

water.

Overflow Combined feed & expansion tank

Stop cock

V.

Cold water pipe.

house cistern

R.

The rate of circulation in the ordinary low pressure hot-water system may be considerably accelerated by means of steam injections. The water after being heated passes into a circulating

There are many different systems of heating by hot water circulating in pipes. The oldest and best known is the " two pipe "system, others being the "one pipe " or " simple circuit," and the "drop or overhead." The high pressure system is of later invention, having been first put to practical use by A. M. Perkins in 1845. All these methods warm chiefly by means of convected heat, the amount of true radiation from the pipes being small. The manner in which the circulation of hot water takes place in the tubes is as follows. Fire heats the water in a boiler from the top of which a 66 flow" pipe communicates with the rooms to be warmed (fig. 3). As the water is heated it becomes lighter, rises to the top of the boiler, and passes along the flow It is followed by more and more hot water, and so travels along the flow pipe, which is rising all the time, to the farthest point of the circuit, by which time it has in all probability cooled considerably. From this point the " return " pipe drops, usually at the same rate as the flow pipe rises; and in due course the water reaches its starting point, the boiler, and is again heated and again circulated through the system. The connexion of the return pipe is made with the lower part of the boiler. Branches may be made from the main pipes by means of smaller pipes arranged in the same manner as the mains, the branch flow pipe being connected with the main flow pipe and returning into the main return. To obtain a larger heating surface than

R.

Return

Flow

Return

Flow

Branch V. flow Branch return!

V.

Branch flow

Branch return

Main flow pipe.

Main return pipe

R.

Boiler

R.

empty system

-Tap to

regulating value

R.

R.

R.

R.

Alternative method with separate return pipe

the same water is used over and over again, and no fresh deposit of fur occurs. Owing to the very rapid movement and the consequent increased rate of transmission of heat, the pipes and radiators may be reduced in size, in many circumstances a very desirable thing to achieve. With this system the temperature XIII. 6

can be quickly raised and easily controlled. If the weather is mild, a moderate heat may be obtained by using the apparatus as an ordinary hot water system, and shutting off the steam injectors.

The cold-water supply and expansion tank (fig. 3) are often combined in one tank placed at a point above the level of circulation. The tank should be of a size to hold not less than a twentieth part of the total amount of water held in the system. The automatic inlet of cold water to the hot water system from the main house tank or other source is controlled by a ball valve, which is so fixed as to allow the water to rise no more than an inch above the bottom of the tank, thus leaving the remainder of the space clear for expansion. An overflow is provided, discharging into the open air to allow the water to escape should the ball valve become defective.

Expansion chamber

Filler

V.

V.

܂

Lavatory basin

Flow pipes

Return pipe

ball

C

* Cold water supply to

Tank

heated by eoil

C. denotes radinting coll " regulating valve

V.

The "Perkins" or "small bore high pressure system (fig. 6) has many advantages, for it is safe, the boiler is small High and is easily managed, the temperature is well under pressure control and may be regulated to suit the changing hot weather, and the small pipes present a neat appearance water. in a room. The whole system is constructed of wrought iron pipe of small diameter, strong enough to resist a testing pressure of 2000 to 2500 lb per sq. in. The boiler consists of similar pipe coiled up to form a fire-box, inside which the furnace is lighted. The coil is encased with firebricks and brickwork, and the smoke from the fire is carried off by a flue in the ordinary way. The flow pipe of similar Tank of water section (usually having an internal diameter of about 1 in., the metal being nearly in. thick) continues from the top of the coil, and after travelling round the various apartments returns to, and is connected with, the lowest part of the boiler coil. The joints take a special form to enable them to withstand the great strain to which they are subjected (fig. 7). One end of a pipe is finished flat, the end of the other pipe being brought to a conical edge. On one end also a right-handed, and on the other a left-handed, screwthread is turned. A coupling collar, tapped in the same manner, is screwed on, and causes the conical edge to impress itself tightly on the flat end, giving a sound and lasting joint. The system is hermetically sealed after being pumped full of water, an expansion chamber in the shape of a pipe of larger dimensions being provided at the top of the system above the highest point of circulation. Upon the application of heat to the fire-box coil the water naturally expands and forces its way up into the expansion chamber; but there it encounters the pressure of the confined air, and ebullition is consequently prevented. Thus at no time can steam form in the system. This system is trustworthy and safe in working. The smallness of the pipes renders it liable to damage by frost, but this accident may be prevented by always keeping in frosty weather a small fire in the furnace. If this course is inconvenient, some liquid of low freezing-point, such as glycerine, may be mixed with the water.

Plug

Boiler coil

In the low pressure two pipe system the flow pipe is carried to a sufficient height directly above the boiler to allow of its gradual fall to a little beyond the most distant point at which connexion is to be made with the return pipe, which thence slopes towards the boiler. Branches are taken off the flow pipe, and after circulating through coils or radiators are connected with the return pipe. In a well-proportioned system the pressure need not exceed 2 or 3 lb per sq. in. for excellent results to be obtained. The one-pipe system is similar in principle, the pipe rising to its greatest height above the boiler and being then carried around as a single pipe falling all the while. It resembles in many points the one-pipe low pressure hot-water system. Radiators are fed directly from the main. Where, as in factories or workshops, there are already installed engines working at a high steam pressure, say 120 to 180 lb per sq. in., a portion of the steam generated in the boilers may be utilized for heating by the aid of a reducing valve. The steam is passed through the valve and emerges at the pressure required generally from 3 lb upwards. It is then used for one of the systems described above.

High-pressure steam-heating, compared with the heating by low pressure, is little used. The principles are the same as those applied to low-pressure work, but all fittings and appliances must, of course, be made to stand the higher strain to which they are subjected.

66

The minus pressure steam system, sometimes termed "atmospheric or vacuum," is of more recent introduction than those just described. It is certainly the most scientific method of steam-heating, and heat can be made to travel a greater distance by its aid than by any other means. The heat of the pipes is great, but can be easily regulated. The system is economical in fuel, but needs skilled attendance to keep the appliances and fittings in order. The steam is introduced into the pipes at about the pressure of the atmosphere, and is sucked through the system by means of a vacuum pump, which at the same operation frees the pipes from air and from condensation water. This pumping action results in an extremely rapid circulation of the heating agent, enabling long distances to be traversed without much loss of heat.

Compared with heating by hot water, steam-heating requires less piping, which, further, may be of much smaller diameter to attain a similar result, because of the higher temperature of the heat yielding surface. A drawback to the use of steam is the fact that the high temperature of the pipes and radiators attracts and spreads a great deal of dust. There is also a risk that woodwork near the pipes may warp and split. The apparatus needs constant attention, since neglect in stoking would result in stopping the generation of steam, and the whole system would almost immediately cool. To regulate the heat it is necessary either to instal a number of small radiators or to divide the radiators into sections, each section controlled by distinct valves; steam may then be admitted to all the sections of the radiator or to any less number of sections as desired. In a hot-water system the heat is given off at a lower temperature and is consequently more agreeable than that yielded by a steam-heating apparatus. The joint most commonly used for hot-water pipes is termed the "rust " joint, which is cheap to make, but unfortunately is inefficient. The materials required are iron borings, sal-ammoniac and sulphur; these are mixed together, moistened with water, and rammed into the socket, which is previously half filled with yarn, well caulked. The materials mixed with the iron borings cause them to rust into a solid mass, and in doing so a slight expansion takes place. On