 | New England Water Works Association - Water-supply - 1902 - 508 pages
...Specimen bars of the metal used, each being twenty-six inches long by two inches wide and one inch thick, shall be made without charge as often as the engineer may direct" (ie, left optional with the engineer). In other words, if 'there is no engineer, the foundry will not... | |
 | William Hubert Burr - Building materials - 1903 - 1146 pages
...Material. Sec. 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and i inch thick, shall be made without charge as often as the...metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the centre, shall for pipes 12 inches or less in diameter support a load... | |
 | William Hubert Burr - Building materials - 1903 - 1144 pages
...Material. Sec. 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and 1 inch thick, shall be made without charge as often as the...metal The bars, when placed flatwise upon supports 24 inches apart and loaded in the centre, shall for pipes 12 inches or less in diameter support a load... | |
 | William Hubert Burr - Building materials - 1903 - 1162 pages
...the cost and expense of the contractor, as often as the engineer may direct, and the inspector shall test at least one bar from each heat or run of metal. The bars when placed flatwise upon knife-edge supports, twenth-four (24) inches apart and loaded in the centre, shall support a load of... | |
 | Gaetano Lanza - Engineering - 1905 - 974 pages
...MATERIAL. SECTION 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and i inch thick, shall be made without charge as often as the...metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the centre, shall for pipes 12 inches or less in diameter support a load... | |
 | United States Cast Iron Pipe and Foundry Co - Cast-iron pipe - 1906 - 168 pages
...* SECTION 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and 1 inch thick, shall be made without charge as often as the...metal. The bars, when placed flatwise upon supports 24 inches apart, and loaded in the center, shall support a load of 1,800 pounds and show a deflection... | |
 | Nisbet Latta - Gas manufacture and works - 1907 - 502 pages
...MATERIAL. SECTION 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and 1 inch thick, shall be made without charge as often as the...metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the center, shall for pipes 12 inches or less in diameter support a load... | |
 | American Society for Testing Materials - Building materials - 1910 - 326 pages
...MATERIALS. SECTION 9. Specimen bars of the metal used, each being 26 inches long by 2 inches wide and 1 inch thick, shall be made without charge as often as the...metal. The bars, when placed flatwise upon supports 24 inches apart and loaded in the center, shall, for pipes 12 inches or less in diameter, support a load... | |
 | William Hubert Burr - Building materials - 1911 - 1124 pages
...the cost and expense of the contractor, as often as tVie engineer may direct, and the inspector shall test at least one bar from each heat or run of metal. The bars when placed flatwise upon knife-edge supports, twenth-four (24) inches apart and loaded in the centre, shall support a load of... | |
| |
Specimen bars of the metal used, each being 26 inches long by 2 inches wide and 1 inch thick, shall be made without charge as often as the engineer may direct, and, in default of definite instructions, the contractor shall make and test at least one bar... 
